Openwrt - Revision history

Reset: /* Reset DHCP OpenWrt */

2018-08-19T00:45:29Z

Reset DHCP OpenWrt

← Older revision		Revision as of 00:45, 19 August 2018
Line 41:		Line 41:

	==Reset DHCP OpenWrt==		==Reset DHCP OpenWrt==

			uci set network.lan.proto=static
			uci set network.lan.ipaddr=192.168.1.10
			uci set network.lan.gateway=192.168.1.1
			uci set network.lan.netmask=255.255.255.0
			uci set network.lan.dns=8.8.8.8
			uci dhcp commit

	==Birdge AP==		==Birdge AP==

Reset: /* Birdge AP */

2018-08-19T00:45:15Z

Birdge AP

← Older revision		Revision as of 00:45, 19 August 2018
Line 39:		Line 39:

	uci commit dhcp		uci commit dhcp

			==Reset DHCP OpenWrt==

	==Birdge AP==		==Birdge AP==

Reset: /* Birdge AP */

2018-08-09T19:47:38Z

Birdge AP

← Older revision		Revision as of 19:47, 9 August 2018
Line 41:		Line 41:

	==Birdge AP==		==Birdge AP==
			The changes below assume an OpenWrt default configuration, the relevant files are:

			/etc/config/network
			/etc/config/wireless
			Step 1: Change the LAN interface
			Edit /etc/config/network and change the lan interface section to set the IP your access point should have in the future:

			config interface lan
			option ifname eth0
			option type bridge
			option proto static
			option ipaddr 192.168.1.2
			option netmask 255.255.255.0
			option gateway 192.168.1.1
			option dns 192.168.1.1
			This IP address must be an unused one within the network subnet of the main router. You could also change proto to dhcp and let the main router decide the access point's address, but of course from then on the access point needs a DHCP server and you will lose the ability to directly plug into your access point for maintenance.

			Step 2: Configure and enable the wireless network
			In /etc/config/wireless, locate the existing wifi-iface section and change its network option to point to the newly created interface section.

			config wifi-iface
			option device wifi0
			option network lan
			option mode ap
			option ssid OpenWrt
			option encryption none
			Naturally, you should consider securing your wifi network.

			Step 3: Disable dnsmasq
			/etc/init.d/dnsmasq disable
			Step 4: Connect host router and openwrt router correctly
			Ensure the host router is connected with a lan port of the openwrt, not the wan port!

			Apply changes
			Enable the new wireless network.

			root@OpenWrt:~# ifup wifi
			root@OpenWrt:~# wifi

	==Traffic Monitor==		==Traffic Monitor==

Reset: /* Failsafe mode */

2018-08-09T19:47:30Z

Failsafe mode

← Older revision		Revision as of 19:47, 9 August 2018
Line 39:		Line 39:

	uci commit dhcp		uci commit dhcp

			==Birdge AP==

	==Traffic Monitor==		==Traffic Monitor==

Reset at 00:37, 20 July 2018

2018-07-20T00:37:36Z

← Older revision		Revision as of 00:37, 20 July 2018
Line 1:		Line 1:

	~~opkg install nmap~~


	~~opkg install nmap~~

	==Failsafe mode==		==Failsafe mode==

Reset at 00:37, 20 July 2018

2018-07-20T00:37:10Z

← Older revision		Revision as of 00:37, 20 July 2018
Line 50:		Line 50:
	iftop -i br-lan		iftop -i br-lan

	==~~Links==~~		==OpenVPN==
	~~https://wiki.openwrt.org/toh/tp-link/tl-wdr3600~~

	~~183~~
	~~209~~

	~~==Traffic Monitor==~~
	~~opkg install iftop~~

	~~iftop -i br-lan~~

	~~==Links~~==
	https://wiki.openwrt.org/toh/tp-link/tl-wdr3600		https://wiki.openwrt.org/toh/tp-link/tl-wdr3600

	183		183
	209		209

Reset at 20:46, 1 July 2018

2018-07-01T20:46:05Z

← Older revision		Revision as of 20:46, 1 July 2018
Line 2:		Line 2:
	opkg install nmap		opkg install nmap


			opkg install nmap

			==Failsafe mode==


			1. Set your PC ip: 192.168.1.2 and subnetmask 255.255.255.0 and gateway 192.168.1.1

			2. Power off the router

			3. Disconnect the WAN cable

			4. Only connect your PC Ethernet cable to ETH0

			5. Power On the router

			6. Wait for the router to start the boot sequence (SYS LED starts blinking)

			7. When SYS LED is blinking, hit restart button (SYS LED will be blink in a faster rate means your router is in failsafe Mode) (you have to hit the button before the router boots)

			8. telnet 192.168.1.1

			9. run these commands

			mount_root ## this remounts your partitions from read-only to read/write mode

			firstboot ## This will reset your router after reboot

			reboot -f ## And force reboot

			Login the web interface using web browser.


			mount_root

			uci set network.lan.proto=static
			uci set network.lan.ipaddr=192.168.1.10
			uci set network.lan.netmask=255.255.255.0
			uci set network.lan.gateway=192.168.1.1
			uci set network.lan.dns=8.8.8.8

			uci commit dhcp

			==Traffic Monitor==
			opkg install iftop

			iftop -i br-lan

			==Links==
			https://wiki.openwrt.org/toh/tp-link/tl-wdr3600

			183
			209

	==Traffic Monitor==		==Traffic Monitor==

Reset at 05:33, 24 June 2018

2018-06-24T05:33:31Z

← Older revision		Revision as of 05:33, 24 June 2018
Line 10:		Line 10:
	==Links==		==Links==
	https://wiki.openwrt.org/toh/tp-link/tl-wdr3600		https://wiki.openwrt.org/toh/tp-link/tl-wdr3600

			183
			209

Reset at 05:16, 24 June 2018

2018-06-24T05:16:33Z

← Older revision		Revision as of 05:16, 24 June 2018
Line 1:		Line 1:

			opkg install nmap


	==Traffic Monitor==		==Traffic Monitor==

Reset: /* Traffic Monitor */

2018-06-24T05:16:03Z

Traffic Monitor

← Older revision		Revision as of 05:16, 24 June 2018
Line 2:		Line 2:
	==Traffic Monitor==		==Traffic Monitor==
	opkg install iftop		opkg install iftop

	iftop -i br-lan		iftop -i br-lan

			==Links==
	https://wiki.openwrt.org/toh/tp-link/tl-wdr3600		https://wiki.openwrt.org/toh/tp-link/tl-wdr3600